Renishaw雷尼绍 OMP400机床测头-价格优惠

品Pai：	雷尼绍Renishaw	型号：	OMP400j机床测头
测量范围：	工件找正及工件检测

OMI-2的OMP400测头超小型高精度测头.OMP400测头可配用新型的OMI-2集成接口接收器.OMP400测头适用高精度及复杂零件3D测量，重复精度高达0.25μm产品描述：●配有OMI-2的OMP400测头超小型高精度测头●超小型设计—直径仅40mm，长度仅50mm●重复性极高的应变片技术●能够使用长达200mm的测针●三维性能，能够测量立体表面，同时维持很高的精度●十分适合对加工公差要求严格的超小型、小型和中型加工ZXAbout OMP400The OMP400 is an ultra compact probe, ideally suited to small to medium machining centres. It combines the miniaturisation of the highly successfulOMP40probe with new advances in strain gauge technology, pioneered by Renishaw's high accuracyMP700probe.Strain gauges attached to the structure measure the smallest of stylus motions, allowing for a very sensitive system.The innovative RENGAGE™ technology built into the OMP400 brings unrivalled performance in terms of 3D measurement. Use OMP400 withRenishaw OMVfor advanced on-machine verification when machining contoured surfaces and complex shapes.OMP400 features and benefitsPatented RENGAGE™ technology brings unrivalled performance in terms of 3D measurement.Increased stylus lengths can be supported without a significant decrease in probe performanceCompatible with all existing Renishaw receiver interfaces (modulated:OMI-2TandOMI-2C;legacy:OMIandOMM / MI 12)The OMP400 sets new standards for reliability and, sealed to IPX8, OMP400 is designed to resist the harshest machine conditionsOMP400 system options

OMP400 withOMI-2T

OMP400 withOMI-2

OMP400 withOMI

OMP400 withOMM / MI 12

Offers twin probing option.		Offers a state-of-the-art modulated optical transmission method.		Ideal for factory fitment by machine tool builders.		Offers installation flexibility making it ideally suited for retro-fitting in the field.

OMP400 specification

Specification

Principal application	Small to medium machining centres and mould & die applications
Weight (without shank in g) with batteries without batteries	262 g (9.24 oz) 242 g (8.53 oz)
Sense directions	Omni-directional: ± X, ± Y, +Z
Uni-directional repeatability	0.25 µm (10 µin) 2 sigma – 50 mm stylus length* 0.35 µm (14 µin) 2 sigma – 100 mm stylus length
2D lobing in X, Y	± 0.25 µm (10 µin) 2 sigma – 50 mm stylus length* ± 0.25 µm (10 µin) 2 sigma – 100 mm stylus length
3D Lobing in X, Y, Z	± 1.00 µm (40 µin) 2 sigma – 50 mm stylus length* ± 1.75 µm (70 µin) 2 sigma – 100 mm stylus length
Trigger speed range	10 mm/min to 1 m/min
Stylus trigger force** XY plane + Z direction	0.06 N, 6 gf (0.22 ozf) typical minimum 2.55 N, 260 gf (9.17 ozf) typical minimum
Stylus overtravel force** XY plane +Z direction	1.04 N, 106 gf (3.74 ozf) typical minimum§ 5.5 N, 561 gf (19.78 ozf) typical minimum †
Stylus overtravel XY plane +Z direction	± 11° 6 mm (0.23 in)
Battery life - stand-by - 5% usage - continuous life	Legacy / Modulated mode One year 90 / 110 days 110 / 105 hours
Sealing	IP X8 (BS 5490, IEC 529) 1 atmosphere
Shanks	Various
Compatible interface	Legacymode:OMIorOMM / MI 12 Modulatedmode:OMI-2orOMI-2T

* Performance specification is for a test velocity of 240 mm/min (9.45 in/min) with a 50 mm carbon fibre stylus. Test velocity does not constrain performance in application.** The stylus trigger force is the force exerted on the component when the probe triggers. However, the maximum force applied to the component will occur after the trigger point and will be greater than the trigger force. The magnitude depends on a number of factors affecting probe overtravel includingmeasuring speed and machine deceleration. If the forces applied to the component are critical, contact Renishaw for further information.§ Stylus overtravel force in XY plane occurs 70 µm after the trigger point and rises by 0.1 N/mm, 10 gf/mm (9.1 oz/in) until the machine tool stops (in the high force direction and using a 50 mm carbon fibre stylus).† Stylus overtravel force in + Z direction occurs 10 to 11 µm after the trigger point and rises by 1.2 N/mm, 122 gf/mm (109.6 oz/in) until the machine tool stops.OMP400 software optionsThe following software packages can be used to program probing routines for work piece set-up and inspection on CNC machining centresEasyProbe- entry-level package for simple work piece set-upInspection- basic set-up and work piece inspection cycles, with automatic update of offsetsInspection Plus- an integrated suite of inspection cycles including vector measurementProductivity+ Active Editor Pro- a PC-based software package with GUI, allowing the user to select features directly from an imported CAD model, making the generation of probing cycles even easier.Renishaw OMV- A PC-based software package for verification of complex parts and live data capture to PC during probing for instant feedback on component quality.