捷克VUHZ.A.S是世界的结晶液位传感器制造商,产品广泛地应用于世界各大钢厂,在ZG,宝钢,鞍钢,首钢京唐,唐钢,包钢,邯钢,湘钢,涟钢等大中小型钢厂都在使用VUHZ的液位检测产品.VUHZ产品以其世界上领先的科技水平,突破了传统的检测系统的局限, 传统的检测系统一般采用Co一60或浮球检测系统。其中Co—60检测虽然精度高，但其具有放射性，需要专业人员保管和使用，安全性不高。而浮球是采用耐材制造的，会受到钢水的侵蚀，需定期人为更换和预热，增加操作人员的劳动强度和中断整个控制系统降低铸机的效率。VUHZ公司电磁感应式传感器，测量范围为0～160mm。VUHZ传感器安装在结晶器的顶部。冷却系统采用直接用铸机的一次冷却水闭环冷却，几乎不用另增设备.VUHZ结晶液位控制系统包括有VUHZ液位传感器SH7-S10,VUHZ前置放大器SH-P,VUHZ信号处理器SH-E,VUHZ液位传感器电缆,VUHZ信号处理器连接电缆, VUHZ螺栓,VUHZ传感器安装固定底座,VUHZ传感器保护盖板, VUHZ绝缘保护轴套, VUHZ导向垫板, VUHZ绝缘垫片及VUHZ工具.VUHZ安装结构示意图:document.write('')
VUHZ采购备件清一览表:
| 序号 | 品名 | 规格型号 |
| 1 | VUHZ液位检测传感器 | MOLD LEVEL SENSOR SH7-S10 |
| 2 | VUHZ信号处理器 | EVALUATION UNIT SH-E |
| 3 | VUHZ前置放大器 | PRE-AMPLIFIER SH-P |
| 4 | VUHZ液位检测传感器电缆 | SENSOR CABLE |
| 5 | VUHZ 信号处理器连接电缆 | SET OF CABLES |
| 6 | VUHZ螺栓 | SCREW |
| 7 | VUHZ传感器安装固定底座 | SENSOR HOLDER COMPLETE |
| SENSOR HOLDER |
| SCREW |
| WASHER FOR SENSOR HOLDER |
| 8 | VUHZ传感器保护盖板 | SENSOR COVER |
| 9 | VUHZ绝缘保护轴套 | INSULATION SLEEVE S/S |
| 10 | VUHZ导向垫板 | GUIDE FEATHER COMPLETE |
| ①GUIDE FEATHER |
| ②SCREW DIN963 M8×16-I |
| 11 | VUHZ绝缘垫片 | BOTTOM INSULATION GASKET |
| 12 | VUHZ工具 | VUHZ TOOL SET |
| SIMULATOR PREAMPLIFIER & SENSOR CA |
| SIMULATOR FOR SENSOR CP |
| VUHZ SIMULATION PLATE |
| TORQUE WRENCH WITH ALLEN KEY SET |
| SCREW DRIVER W.OPEN SPANNER SET |
| INSULATION RESISTANCE METER |
| Grease Belzona 8211HP |
| SEAL & BOND FLEX-SIL (RED) |
| GAUGE FOR SENSOR HOLDER POS |
| MOULD LEVEL SIMULATOR H3 |
Mold level measurement is not sensitive to local meniscus disturbances, such as vortices caused by argon blowing, various types of waves, etc. Sensor's viewing field width is approx. 600 mm and sensor measures mean molten steel level at this section of the mold's width. Typical course of characteristic is shown in.2.3 Electromagnetic sensor SH7-S10The sensor has shape of prism. The sensor is made of stainless non-ferromagnetic steel. Two sensing coils are located symmetrically to the axis.The sensor is fastened to the mold by means of sensor cover, which serves as a clamp and which protects the sensor as well. The sensor cover is screwed on to two special holders fixed to the water jacket – see chapter 4. The cable between sensor and pre-amplifier may consist of two parts. Flexible cable is firmly soldered to each sensor. On the mold top an intermediate connector coupling may be placed, which is connected with pre-amplifier by second part of the cable.2.4 BASIC TECHNICAL DATAElectromagnetic sensor SH7-S10Measuring range: 20 to 160 mm below the top edge of the moldNominal range: 60 to 100 mmMinimum mold level that can be indicated: 250 mm (= the lowest indicated level)Minimum mold size: 100 x 600 mm; maximum – no limits.Storing temperature for the sensor without water: 0°C to 60°CSensor is resistant against a short-time molten slag overflow.Steel drops or coherent steel layer are not allowed on the surface of the sensor.Sensor’s cable length: up to 10 mProtection: sensor IP 56, connector on the cable IP 65 (in connected and locked position)Dimensions: see Fig. 1.9Mass: approx. 28 Kg incl. cable in a protective hose (conduit) and connectorRelative humidity: Preamplifier SH-PPower supply: from evaluation unitDimensions: preamplifier is situated in a junction box – size 300 X 300 X 150 mmMass: approx. 7 kgProtection: IP 5mbient temperature: -20 to + 60°CRelative humidity: up to 90%Evaluation unit SH-EOutput signal: 4 to 20 mA or 0 to 20 mA/500 ohmsVUHZ a.s.Digital setting-up of the slope, e.g.: 4 mA = 160 mm, 20 mA = 20 mmVUHZ传感器内部基本结构原理。由励磁线圈S和检测线圈L和检测线圈R组成。励磁采用峰峰值15V频率800HZ的信号。由于浇注时钢液面上有保护渣层，而此励磁产生的电磁信号可以穿透10mm的渣层和18mm钢水。但该电磁信号不能穿透铜板，因此在传感器的其它部位使用铜质的外壳。电磁信号经过钢液面反射回来分别在两个检测线圈上产生与钢液面的高度成相应关系的感应电动势VL和VR。电动势Ve(Ve=VL+VR)和结晶器振动的频率(fo)和振幅(Fo)信号一起作为变送器的输入信号经过补偿、转换成标准的4～20mA液位信号。VUHZ结晶液位控制系统VUHZ液位传感器SH7-S10,VUHZ前置放大器SH-P,VUHZ信号处理器SH-E,VUHZ液位传感器电缆,VUHZ信号处理器连接电缆, VUHZ螺栓,VUHZ传感器安装固定底座,VUHZ传感器保护盖板, VUHZ绝缘保护轴套, VUHZ导向垫板, VUHZ绝缘垫片VUHZ工具.
