泵压力表 KBY
Pump pressure gauge KBY
产品简介
KBY-1A型压力表,主要用于水泵、泥浆泵、排污泵等各类工程施工配套使用。可供地质、煤碳、冶金、化工、水电、轻工、环保及工程施工系统,在生产过程中测量泵压以及压力变化。
该表具有以下特点:
1、耐震性能良好。并能承受测量范围内的瞬间压力冲击;
2、良好的阻尼特性。可测量脉动介质的瞬间压力平均值;
3、防“堵”性能优异。对高粘度、易结晶、含颗粒状和纤维状物质以及油污等复杂介质,具有较强的适应性;
4、仪表采用全密封结构,可在高湿度、粉尘、污溅以及浅水中等恶劣环境中工作;
5、全金属外壳体和器件,坚固可靠;
6、外形美观,度盘清晰。
PRODUCT OVERVIEW
YBY-1A-type pressure gauge, mainly for water pumps, mud pumps, sewage pumps and
other construction necessary use. For geology, coal, metallurgy, chemical industry, water,electricity, light industry, environmental protection and construction systems, in the production process and the pressure pump pressure measurement.
The table has the following characteristics:
1, the seismic performance is good. Measuring range and can withstand the impact of the instantaneous pressure;
2, good damping characteristics.Measure the pulse of the average instantaneous pressure medium;
3, anti-"blocking" performance. The high viscosity and crystallization, with granular and fibrous material, and oil and other complex media, with a strong adaptability;
4, instrument Fully sealed structure, high humidity, dust, dirt and splashing in shallow water medium harsh environment;
5, full metal body and components, solid and reliable;
6, beautiful appearance, clear dial.
主要技术参数
1、表头公称尺寸(㎜)¢116(整体几何尺寸116×234×54)
2、系列产品测量范围及精度等级
测量范围MPa | 精度等级 |
0-1、0-1.6、0-2.5、0-4、0-6、 0-10、0-16、0-25、0-40、0-60 | 2.5 |
3、工作环境温度 -10~45℃ 相对湿度 ≦90%
4、介质脉动频率20~50次/分
5、环境震动频率≦25HZ; 震动范围 ±0.5㎜
6、安装螺纹 M20×1.5
Specifications
1 meter Nominal Size (mm) ¢ 116 (the overall geometry of 116 × 234 × 54)
2, the series measurement range and accuracy classRange MPa accuracy class
0-1,0-1.6,0-2.5,0-4,0-6,
0-10,0-16,0-25,0-40,0-60 2.5
3, Working temperature -10 ~ 45℃Relative Humidity≦90%
4, medium pulsation frequency of 20 to 50 times / min
5, environmental vibration frequency≦25HZ; vibration range of ± 0.5 mm
6 Mounting thread M20 × 1.5
结构及工作原理
KBY-1A型压力表,由介质转换器(或称隔离器)和表头组成。
介质转换器主要组件有:器体、橡胶隔膜(隔膜上部充20#机油或不同粘度的甲基硅油为工作油,使隔膜变呈Ω状)、注油接头、安装接头等;表头由弹簧元件、传动机构、度盘、阻尼器以及壳体组成。表头内腔充粘度为300-500cs的甲基硅油。
被测介质的压力推动隔膜,介质转换器中的工作油以同等压力使弹簧元件自由端产生相应的位移,经传动机构,表针旋转指示出被测介质的压力值。
Structure and working principle
KBY-1A-type pressure gauge, by the media converter (or isolation) and the header component.
Media converters main components are: device body, the rubber diaphragm (diaphragm or the upper part of the oil charge of 20 # methyl silicone oil of different viscosity oil for the work, so that change was Ω-shaped membrane), grease fittings, installation and other joints; Meterby the spring element, transmission, dial, dampers, and shell composition.Header cavity filling for the 300-500cs viscosity of methyl silicone oil.
The pressure measured media to promote the diaphragm, media converters work in the oil to the same pressure to produce the corresponding free end of the spring element of displacement, the transmission mechanism, hands rotate indicate the pressure value measured media.
使用注意事项
1、被测介质压力应不大于所选用仪表测量上限的3/4;
2、仪表垂直安装为宜;
3、使用过程中,严禁拆动各零、部件;
4、若出现表头内腔充油漏失严重或介质转换器内工作油渗漏,以及隔膜破裂等情况,应及时停用;
5、开箱后的仪表应放在下述环境中保管;
(1) 环境温度+5~45℃;
(2) 相对湿度≦85%;
(3) 空气中不应含有腐蚀性气体和杂质;
6、存放一年以上的仪表,启用前应进行检测。
Caution
1, measured media pressure should not exceed the maximum measurement instrument of
choice 3 / 4;
2 meter vertical installation is appropriate;
3, the use, is strictly prohibited dismantled parts and components;
4, If there is severe leakage meter oil-filled cavity or media converter to work the oil leakage,and membrane rupture, etc., should be promptly suspended;
5, after the meter box shall be kept on the following environments;
(1) Ambient temperature +5 ~ 45℃;
(2) relative humidity≦85%;
(3) the air should not contain corrosive gases and impurities;
6, stored more than one year of the instrument, should be detected before the opening.
咨询订购泵压力表
: 56291930
:sales@zoriver.cn
公司:http://www.zoriver.cn http://www.zoriver.cm.cn