产品简介:
▲逆转电流自动消除停滞电动势
▲保护达到 600V
▲自动探测电压和电流导线连接的连贯性
▲多种工作模式包括全部自动
产品特征:
▲轻便和手提式设计使仪器可在室内外使用
▲四线式原理设计能够真实的测的被测物品的阻抗
▲4 1/2 LED数字显示能够清楚的显示测试结果并减少人为的失误
▲用触发和逆转电流的测量方法来消除作用在测试样品上的停滞电压的影响
▲检查测试时候的噪音,减少有可能对测试结果有影响的因素
▲自动探测 P和C电路的连贯性,防止由于高阻抗连接而产生的错误的读数
▲电池模块上能够在电池没和仪器连接的时候显示剩余的电量
产品应用:
▲开关、断路器接点(触点)的阻抗 (接触电阻)
▲母线和电缆线接头
▲飞机扛架的连接和静态控制电路
▲焊接接缝的完整
▲高达 600V的电池系统的内部连接
▲电阻分量的质量控制
▲变压器和电动机绕组阻抗
▲铁轨和轨道之间的粘合
▲金属合金,焊缝和保险丝阻抗
▲石墨电极和其他合成物
▲金属丝和电缆线阻抗
▲发射天线和避雷针
产品主要功能:
▲正常模式
▲自动模式
▲连续模式
▲感应模式
产品技术指标:
| 满偏电压 | 测试电流 |
满偏值 | 分辨率 | 精确度 | 阻抗 | 感抗 | 阻抗 | 感抗 |
1.9999 mΩ | 0.1 μΩ | ±0.2%±0.2μΩ | 20 mV | N/A | 10A | N/A |
19.999 mΩ | 1μΩ | ±0.2% ±2μΩ | 20 mV | 20 mV | 1A | 1A |
199.99 mΩ | 10μΩ | ±0.2% ±20μΩ | 20 mV | 200 mV | 100mA | 1A |
1.9999Ω | 100μΩ | ±0.2% ±0.2 mΩ | 20 mV | 200 mV | 10mA | 100mA |
19.999Ω | 1mΩ | ±0.2% ±2 mΩ | 20 mV | 200 mV | 1mA | 10mA |
199.99Ω | 10mΩ | ±0.2%±20 mΩ | 20 mV | 200 mV | 100 μA | 1mA |
1999.9 Ω | 100mΩ | ±0.2%±0.2Ω | 200 mV | 200 mV | 100 μA | 100μA |
DLRO 10、DLRO 10X产品技术指标对比:
| | DLRO 10 | DLRO 10X |
测量 | 模式 | 正常、自动、连续、高电压 | 正常、自动、连续、高电压、单向 |
控制 | 全自动 | 全自动/手动 |
速度 | <3S数字七段LED显示 |
显示 | 测量 | 4 1/2 LED数字显示 | 大型背光LED数字显示 |
试验原理 | | 单相循环回动直流比率测试法 显示平均值 |
精确度 | | ±10% |
试验电流 | | <10ppm每秒 |
Z大导线阻抗 | | 不考虑电池状况在工作电流10A时为:100 mΩ |
电压表输入阻抗 | | >200KΩ |
抗噪音干扰 | | 在频率为50/60Hz,要小于100mV电压的1%±20,在电压端当噪音超过这个水平,报警器会响起 |
数据 | 输出 | | 通过RS232端口实时传输和下载 |
存储 | | 700组测试数据 |
备忘录大小 | | 通过键盘输入Z多256个字(每个试验) |
电池 | 容量 | 7Ah铅酸可充电电池 |
寿命 | 在10A的工作电流下,按常规可测试1000次 |
充电 | 通过90V~260V,50/60Hz交流,或者12V~15V直流充电 |
充电频率 | 标准 | 2.5个小时充至90%,4个小时充满 |
温度 | 操作 | +5℃~45℃ |
存储 | -10℃~50℃ |
标准 | -30℃~70℃ |
系数 | <0.01% per℃ over range 5℃ to 40℃ |
慢速充电 | <0.01% per℃ from 5℃ to 40℃ |
快速充电 | 0℃~45℃ |
温度(Z大) | | +10℃~45℃ |
湿度(Z大) | | 90%RH 非冷凝 |
海拔(Z高) | | 2000米 |
安全标准 | EMC | 符合EN61010-1600V,类别III,和EN50081和EN50082(1992)标准 |
外形尺寸 | | 220X100X237mm |
重量 | | 2.6Kg(包括电池、模块) |
产品标准配置:
两个测试杆(其中1个带指示灯) 线长1.2米
充电器1个
电源适配器1个
7Ah镍氢可充电电池
用户使用手册(英文)
保修卡1份
MEGGER DLRO10 and DLRO10X
Digital Low Resistance Ohmmeters
• Accurate results in under three seconds
• Auto current reversal cancels standing emfs
• Fuse protected to 600 V
• NiMH battery reduces weight
• 250 mW power limit (with optional override) to avoid heating the test sample
• Automatically detects continuity in potential and current connections
• Visible warning of high voltages present at the terminals
• Visible warning of current flowing in the test sample
• Multiple operating modes including fully automatic
• Alpha-numeric keypad for entering test notes (DLRO10X)
• User setable high and low limits (DLRO 10X)
• Autoranging with Manual option (DLRO 10X)
• Printer output and memory (DLRO 10X)
The MEGGER DUCTER DLRO10 and DUCTER DLRO10X bring new standards to low resistance measurement. Both are fully automatic instruments, selecting the most suitable test current, up to 10 A dc to measure resistance from 0.1 µΩ to 2000 Ω on one of seven ranges. For users who desire more control over the measurement process, DLRO 10X uses a menu system controlled by a two-axis paddle to allow manual selection of the test current. DLRO10X also adds real-time download of results and on-board storage for later download to a PC.
Both instruments are built into a strong, lightweight case that is equally at home in the field or in the laboratory. Light enough to be worn around the neck, they are small enough to be taken into areas which were previously too small to access. DLRO 10 uses a large, bright 4-1/2-digit LED display while DLRO 10X has a large, backlit LCD display