华测高精度海绵切割机 HC-X1型
高精度海绵切割机主要简介:本切割机采用新型海绵切割丝代替激光原理,更好解决了,激光产生的高温对试验的双破坏,同时本仪器采用双轴连动机构。 从而保证切割试验的精度。采用新触屏控制,使用更加友好方便。
切割丝休用仿形刀,优点如下:
1.减少碎屑及粉尘。
2。切割高密度到低密度的泡沫
3.JZ的切割
4.没有明显的切割刀痕
2.1 控制系统主要功能
自动:自动运行、空运行、单步运行
手动:电机正反转、回程序零、回机械零、输出控制
程序:程序的编辑,读入、删除、保存
参数:系统参数、系统自检、IO 设置、用户及厂商密码管理等
外部手动:控制电机正反转,启动、暂停、报警、急停等
指令丰富:20 条控制指令
USB:可以直接用 USB 线对系统进行供电,方便开机画面及程序的传输,学习与操作
隔离 IO 口:带有与系统隔离的输入输出口,输出口能力Z大可到 1A
背面直接出端子接口:减少转接板,背面端子可以直接接线,清晰方便并且节省成本
2.2 系统组成
控制系统主要由以下几部分组成:
1高性能、高速度 32 位
2 液晶显示器(分辨率:192×64)
3 专用运动控制芯片(信号输出为:5V 脉冲+方向)
4 输入/输出(14 路光电隔离 24V 输入,8 路光电隔离 24V 输出,单通道额定 500mA)
5 Z大程序行 480 行
6 触点按键阵列(28 键)
2.3 技术指标
1 Z小数据单位:0.001mm
2 Z大数据尺寸:±99999.999mm
3 快速运动限速:9000mm/min(当脉冲当量为 0.001mm 时)
4 Z高加工速度限速:9000mm/min(当脉冲当量为 0.001mm 时)
5 Z高脉冲输出频率:150KHz
6 控制轴数:1-4 轴(X,Y,Z,C)
7 联动轴数:X,Y 轴可做直线插补,X,Y 可做圆弧插补
8 电子齿轮:分子:1-99999,分母:1-99999
?8?5 系统主要功能:自动、手动、程序、参数、自检、设置等
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
单位地址:北京海淀区上地信息路2号中关村留学人员创业园D楼
: 56261555 :
网址: 邮箱:
HC-X1 type high precision sponge cutting machine
Main introduction: This machine adopts the new type of sponge cutting wire instead of laser principle, a better solution, temperature of laser produced on the double failure, at the same time, the instrument adopts the biaxial linkage mechanism. In order to ensure the accuracy of cutting test. The touch screen control, the use of more convenient and friendly.
The wire break for the profiling knife, advantages are as follows:
1 reducing the debris and dust.
2. The cutting of high density to low density foam
3 precision cutting
4 there is no obvious cutting knife
The 2.1 main functions of control system
Automatic: automatic operation, operation, single step operation
Manual: the motor reversing, back to zero, zero, program to output control
Program: program editor, read, delete, save
Parameters: the system parameters, system self checking, IO settings, users and manufacturers of password management
External: manual reversing motor control, start, pause, stop alarm, etc.
Instructions: 20 control instruction
USB: can be directly on the system used USB power transmission line, convenient boot screen and procedures, learning and operation
IO: with the input and output port isolation and system separation, the output capacity of up to 1A
The direct terminal interface: reduce the adapter plate, the terminal can direct connection, easy to clean and save cost
2.2 system.
The control system mainly consists of the following parts:
1 high performance, high speed 32
2 liquid crystal display (resolution: 192 * 64)
3 special motion control chip (signal output: 5V pulse + direction)
4 input / output (optical electrical isolation of 14 24V input, 8 way optical electrical isolation of single channel 24V output, rated 500mA)
5 of the largest program for 480
6 contact key array (28 key)
2.3 technical indicators
1 is the smallest unit of data: 0.001mm
2 the maximum data size: 99999.999mm
3 fast movement speed: 9000mm/min (when the pulse equivalent to 0.001mm)
4 the maximum processing speed: 9000mm/min (when the pulse equivalent to 0.001mm)
5 the highest frequency of the pulse output: 150KHz
The 6 axis of control: 1-4 axis (X, Y, Z, C)
7: number of axis X, Y shaft can be linear interpolation, circular interpolation of X, Y can be used
8: molecular electronic gear: 1-99999,: 1-99999.
? 8? 5 main functions: automatic, manual, procedure system, parameter setting, self,
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Address: Beijing Haidian District Shangdi Road 2, Zhongguancun Overseas Students Pioneer Park building D
Tel: 56261555 Fax:
Address: email: