瑞士KALLER氮气弹簧X2400-075
瑞士KALLER氮气缸 瑞士KALLER氮气弹簧
X2400-075
X2400-063
X1000-050
X1000-013
X1000-032
瑞士KALLER氮气弹簧X2400-075
X1000-063
X1000-38
X1000-025
瑞士KALLER氮气弹簧X2400-075
使用注意事项:氮气弹簧为高压密封制品,出厂前经过严格的检查和测试,不允许有任何的气体泄漏现象,因此要求用户正确
地安装和使用,才能确保其安全可靠性和的使用寿命。
1 .当氮气弹簧作为独立部件使用时,安装到模具后,在使用寿命范围内一般无需拆卸维修。
2 .若将氮气弹簧连成系统使用,一般需由经过专门训练的人员或专业人员的指导,应特别注意在气缸中的氮气尚未完全释放前,
严禁 拆卸或进行维修,以防意外事故发生。
3 .氮气弹簧下端的螺钉主要起保护和加强密封作用,不得擅自拆卸和随意敲击。
4 .推荐工作行程≤0 . 9 X S(制造行程),严禁超行程压缩。
5 .被活塞杆上端顶压的工件之接触面与活塞杆轴线的不垂直度应≤1°(即应保持垂直,严禁偏载)。
6 .不可有侧作用力,压缩作用力必须以缸体底部垂直。
7 .氮气弹簧在被压缩后,不要使活塞杆自由空回程,以免引起氮气弹簧内部损坏。
8 .注意保持活塞杆圆柱表面的清洁,避免刮伤或刻痕,严禁敲击碰撞。
9 .严禁将氮气弹簧置于烈日下暴晒和高热源环境中,Z高允许温度8 0°C(特制耐高温氮气弹簧例外) 。
1 0 .氮气弹簧应存放在干燥通风、无腐蚀性气体环境中包装存放; 拆箱安装后如长期不使用时可 在为其表面涂抹油脂保护防腐。
11.不得在氮气弹簧缸体、密封圈等处做任何修改或加工。
1 2 .不得为减小行程而将活塞杆截短。
1 3 .不得对氮气弹簧及其附件进行其它加工。
1 4 .不得以非氮气气体充填氮气弹簧。
1 5 .严禁非专业人员对氮气弹簧进行拆解和改造,否则将导致安全问题。
1 6 .将氮气弹簧底部固定在平整的固定板上,使用过程中,氮气弹簧不允许有摇动或窜动现象。
1 7 .氮气弹簧运输时应使用专用包装物进行包装,不得相互碰撞。
1 8 .报废时请将废氮气弹簧隔离存放,不能与其它产品混装,更不能以重物压在废缸体上。
1 9 .处理时请将氮气弹簧内的气体全部放出后再进行其它处理。
TOAN” Nitrogen Gas Spring contains high pressure nitrogen gas, each of TOAN gas springs is strictly inspected and tested;
any of leaking gas or damages are not allowed. Therefore we ask our customers install and use MASON correctly to ensure their safety
and TOAN’s reliable and suitable lifetime.
1.When gas spring is self-contained, normally there is no need to dismount after being installed in die.
2.At linked mode, only specially trained personnel with good knowledge about products should carry out the maintenance. To
avoid any of accidents, DO NOT attempt maintenance spring until internal pressure is exhausted.
3.Port plug is for the purpose of protection and seal. Do not release and strike.
4.The recommended stroke is less than 90% x stroke.
5.It is necessary to have a flat surf a c e a g a i n s t t h e base of the spring in all circumstances. Contact misalignment should be
minimized < 1°
6.The gas spring should not be subject to side loads. Never allow open clearances in a bottom mount or horizontal application.
7.Do not use the gas spring in such a way that the piston rod is released freely from its compressed position as this could cause
internal damage to the gas spring.
8.Keep piston rod clean. Avoid any of scratch and injury. Protect the piston rod against mechanical damage and contact with fluids.
9.The maximum operating temperature 80℃ (Except special high temperature resistance gas spring) Do not expose gas spring
under sunshine and high heat.
10.Store gas spring under dry and ventilation
11.Do not machine or modify.
12.Do not machine piston rod to fit the stroke.
13.Do not machine cylinder and its parts.
14.Do not charge any of gas except nitrogen.
15.only trained and skilled technicians could mount and connect gas springs; otherwise there will be a safety concern.
16.Use the recommended mount solutions and dispose properly.
17.Pack properly and keep away from bumping while delivering.
18.While disposing, store gas springs separately. Do not mix with other products and put under any of heavy material.
19.Discharge gas completely before discard or any of disposing.
瑞士KALLER氮气弹簧X2400-075
在模具工业中,一直大量使用着弹性元件。这些年来,模具技术和模具制造水平有了很大的发展和提高,工业产品对模具的需求量越来越大,模具朝着精密、复杂、GX、长寿命的方向迅速发展。而原有的常规弹性元件存在着一定的缺点,不能满足这种形势的需要,不能理想地解决冲压工艺的要求,往往影响冲压件质量,使模具结构设计变得比较复杂,影响模具在压力机上更换的时间;同时常规弹性元件占有的模具空间太大,增大了模具制造的成本。例如弹簧、橡皮均存在着需要预紧,才能达到设计所要求的弹压力,而它们的弹压力又是随行程加大而明显地增大,这种弹压力不恒定的性能,可能导致零件不能成行,对拉延压边是很不理想的。对于复杂的拉延成形零件,这个矛盾就显得特别突出,有时只好采用增加工序的办法来解决这类问题。再如弹簧、橡皮的起始力小,这对于要求起始力比较大的弯曲、翻边等工艺,也不理想。由此产生的结果是,冲压制件的质量不稳定,调整模具费时费力。对于集型冲头的冲裁工艺,如采用弹簧或橡皮卸料,往往会遇到模具的卸料空间不够安放弹簧或橡皮,需要加大模具空间来解决问题。科学家可以举出不少这类例子。当前冲压设计人员只能采用气垫来部分弥补这些不足。但是采用压力机气垫时,模具的设计、调整使用者不很方便:由于气压的波动和管道节流损失,气垫所提供的力量也不是很准确;它所占有的空间比较大;需要配备专用的压缩空气站,况且并非所有的压力机均配有气垫。在使用气垫时,模具设计均要受气垫顶杆位置的限制,模具安装调试也不方便。为此,人们努力开发一种新型的弹性功能部件来替代常规的弹性元件,这种新型弹性元件具有更加完善的性能,能代替常规弹性元件,完成常规弹性元件难于完成的性能,氮气弹簧做为新型弱性功能部件也就应运而生。它能够弥补上述不足,简化模具设计、制造、方便模具调整;它可以作为独立部件,安装在模具中使用,也可以设计成一种氧气弹簧系统,做为模具的一部分,参加工作,可以在系统中很方便实现弹压力恒定和延时动作,是一种具有柔性性能的弹性部件。氮气弹簧不仅可以在模具行业中广泛地应用,也可以应用到其他工业领域,如汽车、电子、仪表等行业。由此看来,氮气弹簧的用途相当广泛,它的出现迎合了时代的要求,显然,这项技术的发展如今正是方兴未艾。