南非CCG铠装防爆格兰（CCG E1EX，D1EX cable gland）_详细资料

产品信息

南非CCG铠装防爆格兰（CCG E1EX，D1EX，HTPL，HWPL cable gland）

CCG Products are produced under the quality management system ISO9001-2000 standard underwritten by UL USA. CCG Products are internationally certified to British, CENELEC/ATEX, Chinese, South African IEC and Australian standards where applicable.

D1EX EExde IIC Captive Component Gland MAC - Multi Armour Cone
For use indoors and hazardous areas

E1EX EExde IIC Captive Component Gland MAC - Multi Armour Cone
For use outdoors and hazardous areas (E1W Type)

Ex Corrosion Guard EExde IIC MAC - Multi Armour Cone
For use in highly corrosive and wet environments

Corrosion Guard Lead Seal EExde IIC Gland
For lead sheathed cable

HTPL High Voltage Gland for use with PILC cable
For use in hazardous areas

HWPL High Voltage Gland for use with PILC cable
For use in hazardous areas

CCG BarrierTex^TM A, Barrier EEx d Cable Gland for elastometric single steel wire cable
For use in potentially explosive atmospheres

D1EX EExde IIC captive cone gland
MAC - Multi Armour Cone
Features and Benefits
•For use indoors and hazardous areas.
•Two piece handling, no loose parts.
•Freely rotating captive cone, providing an armour clamp and earth bond
without twisting the armour wires.
•Factory fitted captive elastomeric seals for built-in safety.
•Seals on the inner sheath of the cable.
•Manufactured from high quality brass, nickel plated and stainless steel.
•Complete with polypropylene sealing gasket.

Technical Data
Type D1EX
Gland Material Brass (Nickel Plated), Stainless Steel
Seal Material Thermoplastic Elastomer (Silicone on request)
Cable Type Steel Wire, Braid, Tape Armour
Armour Clamping Multi Armour Cone and Cone Ring
Sealing Area Inner sheath
Optional Accessories Locknut, Shroud, Earth Tag, Adaptor / Reducer
Download Data Sheet Download Assembly Instructions

Standards and Certifications
Hazardous Area Classification

SANS/SABS IEC, AS/NZS IEC, CNEx
Zone 1, 2, 21and 22 Exde IIC and DIP
CENELEC / ATEX
Category 2, Category 3, EExde II 2 GD
Compliance Code
Certification No.
CENELEC / ATEX

EN50014:1997E
DEMKO 01 ATEX 130325X
EN50018:2000E
DEMKO 01 ATEX 130325X
EN50019:2000E
DEMKO 01 ATEX 130325X
EN50281-1-1:1999E
DEMKO 01 ATEX 130325X
SANS / SABS / IEC

SANS/SABS 1213
SABS S/W 449UX
SANS/SABS IEC 60079-0
2000
SABS S/W 449UX
SANS/SABS IEC 60079-1
2001
SABS S/W 449UX
SANS/SABS IEC 60079-7
2001
SABS S/W 449UX
SANS/SABS IEC 60529
1989
SABS S/W 449UX
SANS/SABS IEC 61241.1.1
1999
SABS S/W 449UX
AUSTRALIAN / NEW ZEALAND / IEC
AS/NZS IEC 60079-0
2000
AUS Ex 03.3844X
AS/NZS IEC 60079-1
2002
AUS Ex 03.3844X
AS/NZS IEC 60079-7
2001
AUS Ex 03.3844X
AS               1939
1990
AUS Ex 03.3844X
AS/NZS IEC 61241.1.1
1999
AUS Ex 03.3844X
CHINESE
GB3638. 1-2000 part 1

CNEx09 0427U
GB3638. 2-2000 part 2

CNEx09 0427U
GB3638. 3-2000 part 3

CNEx09 0427U
GB12476. 1-2000

CNEx09 0427U
Ingress Protection IP66/67/68
Operating Temperature -30?C TO +130?C
Download Certification AUS Ex 03.3844X
Download Certification DEMKO 01 ATEX 130325X
Download Certification CNEx09 0427U
Download Permit No SANS/SABS 1213
Download Certification SABS S/W449UX
Special Conditions for Safe Use - X
Glands must be used as part of a certified assembly in surface installations only
Not for use on Exd enclosures that are larger than 2000cm³ volume in group IIC gases in zone 1 areas

E1EX EExde IIC captive cone gland
MAC - Multi Armour Cone
Features and Benefits
•For use outdoors and in hazardous areas. (E1W type)
•Two piece handling, no loose parts.
•Multi Armour captive cone, providing an armour clamp and earth bond for
Steel wire, Braid and Tape armoured cable.
•No need to reverse cones or cone rings or change seals to accommodate
different armour cable.
•Patented disconnect system that allows inspection of armour clamp and
inner seal after assembly.
•Factory fitted captive elastomeric seals for built in safety.
•Seals on both inner and outer sheaths to IP66/68.
•Precision manufactured from high quality brass and nickel plated.
•Complete with a polypropylene gasket.

Technical Data
Type
E1EX
Gland Material
Brass (Nickel Plated)
Seal Material
Thermoplastic Elastomer
(silicone on request)
Cable Type
Steel wire, Braid, Tape Armour
Armour Clamping
Multi Armour Cone and Cone Ring
Sealing Area
Inner and outer sheath
Optional Accessories & Tools
Locknut, Shroud, Earth Tag, Adaptor / Reducer
Download Data Sheet Download Assembly Instructions

Standards and Certifications
Hazardous Area Classification

SANS/SABS IEC, AS/NZS IEC, CNEx
Zone 1, 2, 21and 22 Exde IIC and DIP
CENELEC / ATEX
Category 2, Category 3, EExde IIC 2 GD
Compliance Code
Certification No.
CENELEC / ATEX

EN50014:1997E
DEMKO 01 ATEX 130325X
EN50018:2000E
DEMKO 01 ATEX 130325X
EN50019:2000E
DEMKO 01 ATEX 130325X
EN50281-1-1:1999E
DEMKO 01 ATEX 130325X
SANS / SABS / IEC

SANS/SABS 1213
SABS S/W 451UX
SANS/SABS IEC 60079-0
2000
SABS S/W 451UX
SANS/SABS IEC 60079-1
2001
SABS S/W 451UX
SANS/SABS IEC 60079-7
2001
SABS S/W 451UX
SANS/SABS IEC 60529
1989
SABS S/W 451UX
SANS/SABS IEC 61241.1.1
1999
SABS S/W 451UX
AUSTRALIAN / NEW ZEALAND / IEC
AS/NZS IEC 60079-0
2000
AUS Ex 03.3844X-1
AS/NZS IEC 60079-1
2001
AUS Ex 03.3844X-1
AS/NZS IEC 60079-7
2001
AUS Ex 03.3844X-1
AS/NZS IEC 60529
1989
AUS Ex 03.3844X-1
AS/NZS IEC 61241.1.1
1999
AUS Ex 03.3844X-1
CHINESE
GB3638. 1-2000 part 1

CNEx09 0427U
GB3638. 2-2000 part 2

CNEx09 0427U
GB3638. 3-2000 part 3

CNEx09 0427U
GB12476. 1-2000

CNEx09 0427U
Ingress Protection IP66/67/68
Operating Temperature -30?C TO +130?C
Download Certification AUS Ex 03.3844X
Download Certification DEMKO 01 ATEX 130325X
Download Certification CNEx09 0427U
Download Permit No SANS/SABS 1213
Download Certification SABS S/W451UX
ABS 09-SG435709-PDA
Special Conditions for Safe Use - X
Glands must be used as part of a certified assembly in surface installations only
Not for use on Exd enclosures that are larger than 2000cm³ volume in group IIC gases in zone 1 areas

Ex Corrosion Guard EExde IIC
MAC - Multi Armour Cone
Features and Benefits
•For use in highly corrosive and wet locations.
•Cable gland manufactured from high quality brass and nickel plated.
•Factory fitted captive elastomeric seals for built-in safety.
•The screw-on Corrosion Guard is manufactured from non-corrosive
material to protect the steelwire armour and metal parts of the gland.
•Corrosion Guard screws onto the gland body and seals over the outer
sheath of the cable giving an IP 68 seal.
•Complete with a polypropylene gasket.

Technical Data
Type EX Corrosion Guard
Gland Material Brass (Nickel Plated)
Corrosion Guard Material Glass Reinforced Polyester Compound/PBT
Seal Material Thermoplastic Elastomer
Cable Type Steel Wire, Braid, Tape Armour
Armour Clamping Multi Armour Cone and Cone Ring
Sealing Area Inner & outer sheath & total enclosure of gland
Optional Accessories Locknut
Download Data Sheet Download Assembly Instructions

Standards and Certifications
Hazardous Area Classification

SANS/SABS IEC, AS/NZS IEC, CNEx
Zone 1, 2, 21and 22 Exde IIC and DIP
CENELEC / ATEX
Category 2, Category 3, EExde IIC 2 GD
Compliance Code
Certification No.
CENELEC / ATEX

EN50014:1997E
DEMKO 01 ATEX 130325X
EN50018:2000E
DEMKO 01 ATEX 130325X
EN50019:2000E
DEMKO 01 ATEX 130325X
EN50281-1-1:1999E
DEMKO 01 ATEX 130325X
SANS / SABS / IEC

SANS/SABS 1213
SABS S/W 452UX
SANS/SABS IEC 60079-0
2000
SABS S/W 452UX
SANS/SABS IEC 60079-1
2001
SABS S/W 452UX
SANS/SABS IEC 60079-7
2001
SABS S/W 452UX
SANS/SABS IEC 60529
1989
SABS S/W 452UX
SANS/SABS IEC 61241.1.1
1999
SABS S/W 452UX
AUSTRALIAN / NEW ZEALAND / IEC
AS/NZS IEC 60079-0
2000
AUS Ex 03.3844X
AS/NZS IEC 60079-1
2001
AUS Ex 03.3844X
AS/NZS IEC 60079-7
2001
AUS Ex 03.3844X
AS/NZS IEC 60529
1989
AUS Ex 03.3844X
AS/NZS IEC 61241.1.1
1999
AUS Ex 03.3844X
CHINESE
GB3638. 1-2000 part 1

CNEx09 0427U
GB3638. 2-2000 part 2

CNEx09 0427U
GB3638. 3-2000 part 3

CNEx09 0427U
GB12476. 1-2000

CNEx09 0427U
Ingress Protection IP66/67/68
Operating Temperature -30?C TO +130?C
Download Certification AUS Ex 03.3844X
Download Certification DEMKO 01 ATEX 130325X
Download Certification CNEx09 0427U
Download Permit No SANS/SABS 1213
Download Certification SABS S/W452UX
Special Conditions for Safe Use - X
Glands must be used as part of a certified assembly in surface installations only
Not for use on Exd enclosures that are larger than 2000cm³ volume in group IIC gases in zone 1 areas

Standards and Certifications
ABS 09-SG435709-PDA

Corrosion Guard Lead Seal EExde IIC Gland
Features and Benefits
•For use in highly corrosive and wet locations.
•Cable gland manufactured from high quality brass and nickel plated.
•Lead Seals are supplied to match the exact dimensions of cable given
by the customer.
•The screw-on Corrosion Guard is manufactured from non-corrosive
material to protect the steelwire armour and metal parts of the gland.
•Corrosion Guard screws onto the gland body and seals over the outer
   sheath of the cable giving an IP 68 and deluge proof seal.
•Complete with a brass locknut and polypropylene gasket.

Technical Data
Type EX Corrosion Guard Lead Seal Gland (E2W)
Gland Material Brass (Nickel Plated)
Corrossion Guard Material Glass Reinforced Polyester Compound/PBT
Seal Material Thermoplastic Elastomer and Lead
Cable Type Steel Wire Armour, Lead Sheath
Armour Clamping Captive Cone and Cone Ring
Sealing Area Inner lead sheath and outer sheath
Optional Accessories Locknut
Download Data Sheet Download Assembly Instructions

Standards and Certifications
Hazardous Area Classification

SANS/SABS IEC
Zone 1, 2, 21and 22 Exe IIC and DIP
CENELEC / ATEX
Category 2, Category 3, EExde IIC 2 GD
Compliance Code
Certification No.
CENELEC / ATEX

EN50014      1997E
DEMKO 01 ATEX 130325X
EN50018      2000E
DEMKO 01 ATEX 130325X
EN50019      2000E
DEMKO 01 ATEX 130325X
EN50281      1999E
DEMKO 01 ATEX 130325X
SANS / SABS / IEC

SANS/SABS 1213
SABS S/W 448U
SANS/SABS IEC 60079-0
2000
SABS S/W 448U
SANS/SABS IEC 60079-7
2001
SABS S/W 448U
SANS/SABS IEC 60529
1989
SABS S/W 448U
SANS/SABS IEC 61241.1.1
1999
SABS S/W 448U
Ingress Protection IP66/67/68
Operating Temperature -30?C TO +130?C
Download Certification DEMKO 01 ATEX 130325X
Download Permit No SANS/SABS 1213
Download Certification SABS S/W448U
Special Conditions for Safe Use - X
Glands must be used as part of a certified assembly in surface installations only
Not for use on Exd enclosures that are larger than 2000cm³ volume in group IIC gases in zone 1 areas

HWPL high voltage gland
for use with PILC cable
Features and Benefits
•For terminating PILC steel wire armoured cable 6.6kV to 11kV.
•Mechanically fitted lead seal, seals on the lead sheath of cable
without the need for solder, heating or sweating.
•Safe and simple to use in hazardous areas where a fire risk occurs.
•Steel wire armouring clamped with cone and rotating cone ring.
•Outer seal seals to IP66.
•External earth stud provided.
•Contact CCG for more specific details.

Technical Data
Type HWPL
Gland Material Brass (NickelPlated)
Seal Material Thermoplastic Elastomer and Lead
Cable Type Steel Wire Armour
Armour Clamping Cone and Cone Ring
Sealing Area Inner Lead sheath and outer sheath
Download Data Sheet Download Assembly Instructions

Standards and Certifications
Hazardous Area Classification
ZONE 1 and 2, Exe
Certification No.
787/83642/H1640
Ingress Protection IP66
Operating Temperature -30?C to +130?C

BarrierTex A Barrier EExd Cable Gland
for elastometric, single steel wire, armoured cable
Features and Benefits
•Precision manufactured from high quality brass and nickel plated.
•Provides a barrier seal between the individual cores of the cable.
•Inspectable compound and flameproof chamber.
•Prevents explosive gasses propagating through a cable.
•Prevents gas and moisture migrating through a cable.

Technical Data
Type BarrierTex A
Gland Material Brass (Nickel Plated), Stainless Steel, Bronze
Seal Material CCG FR308 or ST574 compound. Thermoplastic elastomer
Cable Type Armoured cable
Armour Clamping Captive Cone and Cone Ring
Sealing Area Inner compound barrier and outer sheath
Download Data Sheet Download Assembly Instructions

Standards and Certifications
Hazardous Area Classification

SANS/SABS IEC, AS/NZS IEC
Zone 1, 2, 21and 22, Exe, Exd I/IIC Ex tD A21
CENELEC / ATEX
Ex tD A21, Exd I/IIC, Exe I/IIC and DIP
Compliance Code
Certification No.
CENELEC / ATEX

EN60079-0   2006 SIRA 07 ATEX 1044X
EN60079-1   2004 SIRA 07 ATEX 1044X
EN60079-7   2003 SIRA 07 ATEX 1044X
EN61241-0   2006 SIRA 07 ATEX 1044X
SANS / SABS / IEC

SANS 808
SAEx MS/06-425X
SANS/SABS IEC 60079-0 2006 SAEx MS/06-425X
SANS/SABS IEC 60079-1
2004
SAEx MS/06-425X
SANS/SABS IEC 60079-7
2003
SAEx MS/06-425X
SANS/SABS IEC 61241-0
2005
SAEx MS/06-425X
SANS/SABS IEC 61241-1
2005
SAEx MS/06-425X
SANS/SABS IEC 60529
2001
SAEx MS/06-425X
AUSTRALIAN / NEW ZEALAND / IEC
IEC 60079-0
2004
ANZEx 07.4045X
IEC 60079-1
2003
ANZEx 07.4045X
IEC 60079-7
2001
ANZEx 07.4045X
IEC 61241-0
2004
ANZEx 07.4045X
IEC 61241.1
2004
ANZEx 07.4045X
Ingress Protection IP66/67/68 (2m cont.)
Operating Temperature -20?C TO +80?C
Download Certification ITACS ANZEx 07.4045X
Download Certification Sira 07ATEX1044X
Download Certification SAEX MS06-425X (R6)
ABS 09-SG435709-PDA

ZG区分销商：
上海颐品自动化科技有限公司
Shanghai Epin Automation Co.,Ltd.

Website:www.epinautomation。。ｃｏｍ
:sales@epinautomation.com
全国免费:
因为专业，所以放心！

您可能感兴趣的产品


		D1EX EExde IIC Captive Component Gland MAC - Multi Armour Cone For use indoors and hazardous areas

		E1EX EExde IIC Captive Component Gland MAC - Multi Armour Cone For use outdoors and hazardous areas (E1W Type)

		Ex Corrosion Guard EExde IIC MAC - Multi Armour Cone For use in highly corrosive and wet environments

		Corrosion Guard Lead Seal EExde IIC Gland For lead sheathed cable

		HTPL High Voltage Gland for use with PILC cable For use in hazardous areas

		HWPL High Voltage Gland for use with PILC cable For use in hazardous areas

		CCG BarrierTex^TM A, Barrier EEx d Cable Gland for elastometric single steel wire cable For use in potentially explosive atmospheres