恒安底板比压仪主要用于煤矿单体液压支柱增压、测压、测底板比压、无供液系统地段支护抢险

 

 

一、恒安底板比压仪应用领域：

   主要用于煤矿单体液压支柱增压、测压、测底板比压、无供液系统地段支护抢险，液压支柱修理后的压力测试等。

  产品优势：

1、 集增压、测压、测底板比压（配压模）功能于一身，一器多用。

2、 不更换泵站及供液系统，使支柱初撑力达25Mpa以上。

3、 测底板比压时，利用工作面支柱。省去原比压仪专用专柱。降低了劳动强度。

4、 便于携带，灵活方便。

 

二、恒安底板比压仪技术参数：

工作压力：0-40Mpa

泵缸容积：589ML

外型尺寸：700×190×61mm

重量：10kg

操纵手把力矩：66Nm

压模规格：￠40mm、￠60mm、￠80mm、￠130mm

 

三、恒安底板比压仪使用注意事项：

1、 运送及使用时，注意保护压力表防止损坏；取下表时要及时封堵接口，防止杂物进入；安装表时不要用手搬动，要用扳手。

2、 使用前检查各部件安装是否牢固。

3、 使用时先摇动几下操纵杆，排除缸内气体。

4、 使用液体为工作面支柱用液，单独配液时，油、水比不低于工作面要求。

5、 禁止用锤及硬物敲打任何部位。

6、 乳化液要清洁，严禁杂物，以免堵塞。

7、 操作时一般不要超过压力表量程75%。

8、 使用后或长期不用时，要用煤油冲洗干净，以防锈蚀堵塞。

 

四、维修常见问题：

1、 检修时要在整洁场所，清洗橡胶件时，不要浸泡，并要迅速擦干，以防变形、变质。

2、 检修试验合格后方可下井使用。

故障排除：

序号 故障现象 原因 排除方法

1 打压时，压力突然增大 （1）O型密封圈被挤进配合间隙；（2）挡圈损坏 更换

2 （1）手把向上缓缓回弹（2）提手把时压力表数字下降 活塞单向阀漏液 检修单向阀，损坏时更换

3 打压时手感力过大，不出液，无压力显示 单向阀堵塞或锈蚀 拆洗

4 打压时手把快速回弹 单向阀弹簧断折 更换

   First, the application field of Heng＇an floor pressure tester: mainly used for coal mine single hydraulic prop pressurization, pressure measurement, floor pressure measurement, no liquid supply system section support emergency, hydraulic prop repaired pressure test, etc. Product Advantages: 1. It integrates the functions of boosting, pressure measuring ａnd bottom plate specific pressure measuring (pressure distributing die), ａnd it is a multi-purpose device. 2. Without replacing the pump station ａnd the liquid supply system, the initial support force of the prop can reach more than 25 Mpa. 3. When measuring the specific pressure of the floor, use the pillars of the working face. The special column for the original specific pressure meter is omitted. It reduces the intensity of labor. 4. Easy to carry, flexible ａnd convenient. 2. Technical parameters of Heng＇an bottom pressure gauge: working pressure: 0-40Mpa pump cylinder volume: 589ML shape size: 700 *190 *61mm weight: 10kg manipulator handle maximum moment: 66Nm die specification: 40mm, 60mm, 80mm, 130mm3, matters needing attention in using Heng＇an bottom pressure gauge: 1. Protect pressure gauge from damage when transporting ａnd using; Seal up in time when taking down the table Interface to prevent debris from entering; don＇t move the table by hand, use wrench when installing it. 2. Check whether the components are firmly installed before use. 3. Shake the joystick several times before using to remove the gas in the cylinder. 4. The ratio of oil to water is not lower than the requirement of working face when liquid is used as prop of working face. 5. It is forbidden to strike any part with hammer or hard object. 6. The emulsifier should be clean ａnd no impurities should be allowed in order to avoid blockage. 7. When operating, the gauge range should not exceed 75%. 8. After use or long-term use, wash with kerosene to prevent rust ａnd clogging. 4. Common problems in maintenance: 1. In order to prevent deformation ａnd deterioration, it is necessary to clean the rubber parts in a clean place without soaking them ａnd dry them quickly. 2. It can be used in wells only after the overhaul test is qualified. Troubleshooting: Reasons for Serial Number Trouble: When pressed, pressure suddenly increases (1) O-ring is squeezed into fit clearance; (2) Baffle damage is replaced by 2 (1) Hand handle slowly rebounds upward; (2) Pressure gauge digitally decreases when handheld, piston one-way valve leaks liquid to repair one-way valve; when replaced by 3 dozen pressure, hand feeling force is too large, no liquid, no pressure shows one-way valve. Replacement of Fast Rebound One-way Valve Spring Broken When Valve Blockage or Rust Removal Wash 4 is Pressed

冒顶(puking)，指地下开采中，上部矿岩层自然塌落的现象。是由于开采后，原先平衡的矿山压力遭到破坏而造成的。采煤工作中有时有计划地放落上部煤层，也称为“冒顶”。