产品简介: 名称:XLC 9-12调直机电机功率:2.2/7.5kw线径:9-12mm定尺长度:3000mm调直轴转速:2400 r/min调直效率:20m/min整机尺寸:2000mm×
$n | $n |
型号:JX149207铁丝调直切断机TZ1.0-2.5 | $n型号:JX173530直销型钢筋调直切断机XLC9-12 | $n
产品的性能与特点:Product performance and features:
型号Model | TZ1-2.5 |
电源Power | 3N-50HZ-380V |
电容Capacitance(p) | 1.5 |
调直线径Straight line diameter/mm | 1-2.5 |
长度The maximum length/mm | 1500 |
调直转速Straightening speed/mm | 1860 |
重量Weight/kg | 140 |
外形尺寸外形尺寸/mm | 1340*500*800 |
1、本机适用于铁线、不绣钢线、镀锌线、铝线、水(粉)抽线等金属线材的调直切断。
1, This machine is suitable for wire, stainless steel wire, galvanized wire, aluminum, water (powder) draw lines and other metal wire straightening and cutting.
2、送线轮、切刀等且优质合金钢,并通过真空处理,使其具有耐磨性,使用寿命延长。调直块采用铸铁、合金塑料王等,轴类全部采用40CR或45#钢,并经调直处理,齿轮则全部采用锻坯,经高直及齿面高频淬火,硬度高达HRC55-58度。
2, sending wire wheel, cutters and high-quality steel, and by a vacuum process, it has wear, longer life. Straightening blocks made of cast iron, alloy plastic Wang, shafts in all 40CR or 45 # steel, and after straightening process, the gear is used in all forging billet, straight and tooth surface by high frequency hardening, hardness up to HRC55-58 degree
3、调直轴与高直压轮将线材在切断前调直,送线压紧手柄调节送线压紧轮,使线材能均匀送进,调直轴是产品形成的关键所在,通过调直轴上的调直块和调直固定志调整产品的水平垂直,使之符合要求。调节压紧手柄,使线材更加水平垂直和使线材速度增减。后调节枪杆上的白钢刀,使产品长度符合要求。
3, straight shaft with high pressure wheel straight before cutting the wire straightening, wire feeding pressing the pinch roller lever to adjust wire feed, the wire can even feed, direct modulation axis is the key product formed by direct modulation straightening blocks and tone straight shaft fixed to adjust the horizontal and vertical products to conform to requirements. Adjusting the pressing handle, the wire and the wire is more horizontal and vertical production rate increase or decrease. Finally, adjust white blades gun on the length of the product to meet the requirements.
4、速度快,工作性能稳定,操作简单。
4, fast, stable performance, simple operation.
本机所配备的六组调线块,可轻易调直一般的铁线,铜线,铝线,不锈钢线,镀锌线,黑铁线等各种材质的型材!运行平稳,噪音小,速度快,不跑线!
Six ganged wire block the machine is equipped, can easily straighten general wire, copper, aluminum, stainless steel wire, galvanized wire, black wire and other materials profile! Smooth running, low noise, high speed, do not run the line!
直线机尾部导线咀上带有油盒,填上棉布以后再加上润滑油,可以让调线的过程更加顺畅,减少作业过程中的断线现象发生。
Linear machine with the oil nozzle trailing wire boxes, together with the lubricating oil to fill after cotton, can make the process of adjusting the line more smoothly, reducing job during a break occurred.
本机所配开关为快速倒顺开关,速度快,易操作。可一边观察线材的走动情况,一边前进或倒退,使线材顺利走过机台进入定位切断枪。
The machine equipped with the switch for quick inverted switch, fast, easy to operate. Can move around while looking at the wire, the side forward or backward, the wire smoothly through the machine gun into the positioning cut.
本机保养及操作注意事项
The machine maintenance and operation precautions
,本机所采用的电源为3相380伏,千万别要缺相,如缺相,则铁定烧坏电机。
First, the machine used for the 3-phase 380-volt power supply, do not want to phase, such as phase, then definitely burn out the motor.
第二,本机的转运部位请定期加油润滑。
Second, the transfer of parts of the machine periodically lubricated.
第三,安装时请可靠接地。
Third, when installing reliable grounding.
第四,工作时严禁打开机盖,否则万一断线时极易发生工伤事故,此操作要领请切记切记!!!
Fourth, the work is strictly prohibited open the cover, otherwise accidents can easily occur in the event of disconnection, this operating essentials please remember! ! !
第五,枪头部位请对墙,以免跑线时刺伤车间其他工作人员。
Fifth, the tip portion of the wall please, in order to avoid stab workshop run line when other staff.
第六,当一卷线材将调完时,请在剩下三圈时停掉机器,否则剩余线头部位有可能产生甩尾现象,很容易伤到操作工人。如果认为线材弄浪严重,有经验的工人可以用钳子夹着线头推送,但我们并不鼓励这种操作方式。
Sixth, when a roll of wire will transfer finished, please stopped three times during the rest of the machine, otherwise the remaining thread parts may produce drift phenomenon, it is easy to hurt workers in the operation. If you think the wire waves get serious, experienced workers can use pliers
中直线机
名称:XLC 9-12调直机
电机功率:2.2/7.5kw
线径:9-12mm
定尺长度:3000mm
调直轴转速:2400 r/min
调直效率:20m/min
整机尺寸:2000mm×575mm×1300mm
整机重量:580kg
型号 | 线径 mm | 定尺长度 mm | 调直抽转速 r/min | 调直效率 m/min | 电机功率 kw | 整机尺寸 mm |
1-1.8自动调直机 | 1-1.8 | 850 | 1946.5 | 40-50 | 0.55×2 | 2000×290×860 |
1-2.5自动调直机 | 1-2.5 | 850 | 1946.5 | 20 | 0.55×2 | 590×350×860 |
2.5-5自动调直机 | 2.5-5 | 2000 | 1866.7 | 20 | 0.55/1.5 | 1110×390×1140 |
5-9自动调直机 | 5-9 | 2000 | 2400 | 20 | 1.5/5.5 | 1410×540×1300 |
9-12自动调直机 | 9-12 | 3000 | 2400 | 20 | 2.2/7.5 | 2000×575×1300 |
铜铝管自动调直机 | 4-16 | 定制 | 定制 | 45-60 | 1.87 | 2200×600×1400 |
以上参数仅供参考。超出上规格要求,可接受专机定造,可订做方、扁(六角线)异形调直切断机。 |
u机器的性能和特点
1、调直机由机架、调直机构、进给机构、切断机构、直线枪及线架等部分组成。
调直部分由调直轴、调直压块和两端轴承座构成,完成对线材的调直工作。其动力为安装在机架下部的电动机,通过三角胶带带动调直轴高速旋转。
2、调直装置与切断装置分属各自电机传动,互不干涉,前后两组送线机构可保证送线的平稳,两个电机均安装在机器的底部,更能增加机器的稳定。
3、送线轮\切刀等采用优异合金钢,并通过真空处理,使其具有耐磨性,使用寿命延长。调直压块采用铸铁合金塑料王等;轴类全部采用40CR或45#钢,并经调质处理,齿轮则全部采用锻坯,经调质及齿面高频淬火,硬度高达HRC55-58度。适用于镀锌线、粉抽线、水抽线及不锈钢线,可保证线表面无伤痕。
4、下料长度可任意调节,误差小,配合高硬度的上下切刀,使切口更好。
u主要用途
本机广泛适用于圆或扁的铁线、不锈钢线、镀锌线、铝线、水粉线等金属线材的拉直切断。
u机器的安装与调试
1、安装:安装时需将主机及线架放置水平,保证安放平稳,无晃动现象。长轴和直线枪安装后需调整水平,使直线枪线槽与主机进线孔ZX线在同一直线上。
2、调试:试车前,对各运转部件进行清洗,然后对导套内孔及其它部分按润滑要求润滑。试车时,先进行空运转试验,试验时控制电机正反运转,检查各部分是否运转正常,有无异常噪音。确定可靠后可以开始调试线材,通过调整压块和定长镶条,分别保证直线度和所需长度,达到要求后方可开始工作。
本产品信息由(河北慧采科技有限公司)为您提供,内容包括(承德铁丝调直切断机 扎丝调直机 安装流程及注意事项)的品牌、型号、技术参数、详细介绍等;如果您想了解更多关于(承德铁丝调直切断机 扎丝调直机 安装流程及注意事项)的信息,请直接联系供应商,给供应商留言。若当前页面内容侵犯到您的权益,请及时告知我们,我们将马上修改或删除。
沪公网安备 31011502008050号